This 1/3 hp pump can be used with a ¾” garden hose or a 1¾“ sump pump discharge hose to remove up to 30 gallons per minute (1,800 gallons per hour). Remove and clean the filter, and gather all the supplies, then you can start draining your hot tub.
Drain pumps drain the water by dewatering the hot tub leaving only a few inches of water in minutes, not hours.
How to drain a hot tub with a pump. Pump hose, filter hose and the main pipe that distributes all the water. To drain using the spigot: Simply, drop the pump into the tub, flick on its switch and wait as the water flows out.
This will prevent the crack from spreading further. After identifying where the crack is, drill two small holes on either end of it. The fastest way to drain a hot tub is to use a submersible pump.
You can now disconnect the hose from the faucet bib. If you do not have a pump or for some reason, you do not want to use it, you can also drain the water using a garden hose. These usually can be connected to a much thicker hose than a standard garden hose and will pump out the water very fast.
Fluentpower submersible pump 3/4hp 3300gph, oil chamber seal structure, drain clean/dirty water from garden,pond,pool,hot tub,flooded cellar, with float switch and hose connector. It used to take about 10 minutes to drain all of the water out using this method. Hot tub professionals use submersible pumps to quickly drain spas when they are in need.
You need to turn off all hot tub functions and switch it off on your circuit breaker; Turn off the hose, disconnect it from the faucet, and keep it low to the ground. You don’t want the hot tub’s heater or pump to work while the water level is low.
The drill bit should be slightly larger than the crack itself. Be certain to hold the kink in the hose until you get the end that you are holding below the level of the hot tub itself. Garden hose drain is the most popular and cheapest way to drain your hot tub.
Personally, i like using the aquapro apc3000 submersible pump. Use the hot tub drain valve. Depending on the size of your spa, it should take around an hour to drain using the hot tub’s drainage spigot, or ten minutes to drain with a submersible pump.
Turn off the hot tub. Drain the spa using either a submersible pump or a hose attached to the drain plug at the base of the hot tub. You just need to connect a hose, drop the pump into the hot tub and switch it on.
The quickest way to drain a hot tub is with a submersible sump pump. The fastest way to drain a hot tub is by using a submersible pump (found online and in hardware stores). They are also useful for many household tasks that require transferring water from one place to another.
Use a submersible sump pump. Go back to the hot tub and make sure the hose stays at the bottom of the tub as the water level drops. This is to keep the water sealed inside the hose for the time being.
How to drain a hot tub with a hose place the end of a garden hose in the hot tub, dropping it straight down into the water so that it lies on the bottom. Turn the power to the spa off at the circuit breaker. You don’t want the pumps or jets to run while there isn’t any water in the spa.
If you’ve already tried draining a hot tub by connecting a hose to the drain and waiting for the water to clear out, you will be delighted with a drain pump solution. 4.3 out of 5 stars. You can drain your hot tub with a standard garden hose, which can take 2 hours or longer.
There are three most important places in a hot tub that need to be protected during winterizing: Most hot tubs have a drain valve (sometimes called a spigot, drain plug or spa drain) which you can utilize to empty it. This method is suitable for owners of.
Or you can use a submersible pump which takes about 15 minutes.****. Turn off the power to the tub. Do this a couple of feet below where the connection to your hose bib is.
With one, you can drain up to 2,000 gallons of water per hour.